Lishi Auto Pick and Decoder 2-in-1 List and Sequence

There are now 53 lishi auto pick and decoder 2in1:

1 ) HU66 single lifter VAG
2 ) HU66 twin lifter VAG ( 2011 on )
3 ) HU49 VAG
4 ) HU92 BMW 2 track
5 ) HU58 BMW 4 track
6 ) HU100R New BMW 2010 on
7 ) HU64 mercedes 2 track
8 ) HU101 ford
9 ) FO38 ford usa
10) HU100 opel
11) HU43 opel
12) HU46 opel
13) YM28 opel
14) GM37 gm usa 4 height
15) GM37 gm usa 5 height
16) HU83 peugeot/citreon also mini and rover 75
17) VA2T peugeot citreon
18) NE78 , peugeot 406
19) renault courtesy lock
20) renault laguna 3
21) NE72 renault , peugeot , opel vivaro nissan primstar
22) GT15 fiat
23) GT10 fiat
24) sip22 fiat
25) CH1 daewoo/checrolet
26) HU87 suzuki
27) CY24 chrysler
28) GM45 pontiac
29) NSN11 nissan
30) NSN14 missan
31) DAT17 suburu 4 track
32) HYN7R hyundai/kia
33) HY15 hyundai kia
34) HY16 hyundai kia
35) HYN11 hyundai kia
36) HY20 hyundai
37) HY22 hyundai kia
38) MIT11 mitsubishi
39) HON66 honda
40) TOY 2 tracker
41) TOY40 toyota lexus
42) TOY48 toyota lexus
43) TOY43AT toyota lexus
44) TOY43R toyota lexus
45) Proton
46) dedicated mini , mg and rover 75 tool
47) renault A
48) new strengthened and improved lishi premium tibbe
49 ) MAZ24 mazda
50 ) HU92 twin lifter
51 ) HU56 volvo
52 ) NE66 Volvo
53 ) YM30 saab

LISHI Auto Picks

Locks that show a preference to sequence picking

The Lishi picks and the new Lishi Pick and decoder tools will pick each lock that they are designed to open, in one locksmiths hands better than another , as one locksmith will have a heightened level of feel to another , However , it is possible to balance this out with some locks, as some locks prefer being picked in a set sequence.

Due to intolerances of manufacture , certain factors influence a lock to such a degree, that picking to set sequences can simplify and speed up the picking process.

Below list the locks to date that have Proven susceptible to set sequence picking , follow these sequences to both speed up picking and offer more success.

The Locks that have shown as preferring sequence picking are;

HU66 generation 1 VAG Group
HU66 generation 2 VAG Group
HU66 generation 3 VAG Group
HU92 BMW 2 Track
HU100 New Opel
HU101 Ford , New Volvo and New Range rover and Land rover.

We have listed each preferred sequence picking system for these below for you ;

The below picking tips are relevant to both the standard picks and the 2 in 1 pick decoders equally , unless stated Otherwise .

HU66 Generation 1 lock produced from 1997 to 2002 generally .

Far better results will be achieved if the following sequences to picking are followed , insert the tool ad apply tension to the lock via the tensioner and then , Pick positions 1,3,5, and 7 first until set ( all slapping ), then when set , pick positions 2,4,6 and 8 , until each position is slapping , if it doesn?t open then ease back tension slightly and repeat as a wafer will have been overlifted.

But remember , Generation 1 locks , pick and set positions 1 , 3 , 5 and 7 first , and then positions 2 , 4 , 6 and 8 !

HU66 Generation 2 & 3 : lock produced 2002 to 2006 is generation 2 , and the lock produced from 2006 is generation 3.

Pick 1 , 5 , 8 , 4 first then when all are set pick 3762 several times until open

The lock produced after 2002, the heads of the wafers 1,4,5 and 8 are wider, The heads of wafers 2,3,6, and 7 are smaller, so it is easier to pick positions 1,5,8, and 4 into the correct position determined by the slapping feel , once these are set increase tension slightly , and then pick positions 3,7,6, and 2 a few times each. If the lock doesn?t open, pick positions 1,5,8, and 4 again, pick every wafer until all are slapping in their open position and are set . If you have applied too much tension as a bit heavy handed, you need to ease back on the tension slightly, and listen to the sound when you ease off, for dropping wafers that were overlifted, then resume the picking process.

HU92 BMW 2 Track

The BMW HU92 Lock has a sequence it prefers , you need to apply moderate tension and pick positions 1 , 3 , 5 and 7 first , being sure to set each position, ensure each position is slapping.
Once positions 1 , 3 , 5 and 7 are set , you then need to pick positions 2 , 4 , 6 and 8 several times until open, if not opening relax tension a fraction and it will open.

HU100 New Opel sequence picking

The HU100 new opel lock prefers a sequence , you need to apply light tension and pick positions , 1 , 3 , 5 and 7 first until each is in its set position , slapping .
Once positions 1 , 3 , 5 and 7 are all set , you need to pick positions 2 , 4 , 6 and 8 several times until the lock opens.

HU101 Ford , New Volvo , Range Rover and Land Rover

The HU101 lock follows a simple pick sequence using a light to moderate tension , you need to pick the row of 4 wafers first , once set , slapping , you need to pick the row of 6 wafers and the lock should open.

Rating
( No ratings yet )
Like this post? Please share to your friends: